• HAZARDS IDENTIFICATION

Classification of the substance or mixture -

Classification (EC 1272/2008) Not classified as hazardous. Classified as an article.

This product is not hazardous according to article 31 and Annex of the EU REACH Regulations. -

Safety Data Sheet / Heavy Metal Test Report / Technical Data sheet (TDS) - Manufacturers Safety Data Sheet (MSDS)

• FIRST AID MEASURES

Description of first aid measures - Eye contact: Flush with water. Seek medical advice if irritation persists. Immediately flush with plenty of water for 15 minutes. Remove any contact lenses and open eyes wide apart. Get medical attention if any discomfort continues.
Skin contact: :Wipe off and wash with soap and water. Seek medical advice if irritation persists.
Inhalation: Remove to fresh air. Get medical attention if any discomfort continues.
Ingestion: Get medical attention if any discomfort continues.
Most important symptoms and effects, both acute and delayed: Prolonged contact with the skin may cause irritation.
Indication of any immediate medical attention and special treatment needed: No recommendation given, but if in doubt get medical attention promptly.
___________________________________________________________________________________

• FIRE FIGHTING MEASURES

Extinguishing Media - Suitable extinguishing media: Carbon dioxide, foam, dry powder or fine water spray. Water can be used to cool containers exposed to fire.
Unsuitable extinguishing media : None known.
Special hazards arising from substance or mixture - Special protective equipment / procedures: Carbon oxides and traces of incompletely burned carbon compounds. A self-contained respirator and protective clothing should be worn. Keep containers cool with water spray until well after fire is out. Determine the need to evacuate or isolate the area according to your local emergency plan.
Advice for fire-fighters: Special exposure hazards arising from the substance or preparation itself, combustion products and resulting gases
___________________________________________________________________________________

• ACCIDENTAL RELEASE MEASURES

Personal precautions, protective equipment and emergency procedures: Wear proper protective equipment.
Environmental precautions: : Prevent material from entering surface waters, drains and soil.
Methods for containment and cleaning up: Scrape up and place in a container fitted with a lid. Dispose of in accordance with local regulations.
___________________________________________________________________________________

• HANDLING AND STORAGE

Precautions for safe handling: General ventilation is recommended. Avoid skin and eye contact. Do not breathe vapour.
Conditions for safe storage, including any incompatibilities : Keep container closed and store away from moisture. Storage temperature should be between 5° C and 30° C with a relative humidity of < 50 % .
___________________________________________________________________________________

• EXPOSURE CONTROLS / PERSONAL PROTECTION

Personal protective equipment - Respiratory protection: Not necessary.
Hand protection: Protective equipment is not normally necessary. Gloves should be worn where repeated or prolonged contact can occur.
Hand protection: Protective equipment is not normally necessary. Gloves should be worn where repeated or prolonged contact can occur.
Eye protection: Avoid contact with eyes.
Skin protection: Protective equipment is not normally necessary.
Hygiene measures: Exercise good industrial hygiene practice. Wash after handling, especially before eating, drinking or smoking.
___________________________________________________________________________________

• PHYSICAL AND CHEMICAL PROPERTIES

Information on basic physical and chemical properties - Appearance: Foilband, laminated with a fixed foil backing.
Available Foil Colours : Aluminium, Lead look, White
Sealant Colour : Black
Odour: None.
Specific Gravity: 1.6g/cm3
Solubility: Water Solubility: 0 g/l at 25° C
Dynamic Shear Adhesion: 12 N/cm2
90 ° Peel Adhesion: 12 N/cm
180 ° Peel Adhesion: 9 N/cm
Moisture Vapour Transmission Rate (sealant component only): 0.14 g/m2/24hr/mm
Service Temperature Range : -40 to +90 ° C
Shelf life : 24 months when stored flat in original packaging in cool, dry conditions.
___________________________________________________________________________________

• SURFACE PREPARATION

All surfaces should be clean, dry and free from frost, grease and loose materials. When cleaning contaminated substrates, we recommend that propan-2-ol (IPA) is used and allowed to dry prior to the application of the sealant strip. When applying the tape to porous or friable surfaces, it is recommended that the surface be treated with a suitable primer, such as an exterior grade PVA, to seal and stabilise the surface
___________________________________________________________________________________

• APPLICATION

To avoid creasing of the foil, separate the foil and sealant from the backing paper as they are being unwound from the roll. Once applied in place, use a roller to ensure good adhesion to the substrate. Avoid joins in the flashing where possible. Any joints should overlap by at least 120mm and be made with the uppermost piece overlapping on top of the lower strip, so that any water running down will drain freely over the front surface of the flashing. When applying the tape to textured surfaces, such as pebble dash or rough brick, it is recommended that a bead of Low Modulus Silicone is applied to the top edge of the foil to prevent water penetrating down behind the strip
___________________________________________________________________________________

• PACKAGING

The product is normally supplied as a preformed strip on a siliconised release paper. A wide range of dimensions can be supplied. Product dimensions will determine the number of rolls per carton.
___________________________________________________________________________________

• STABILITY AND REACTIVITY

Reactivity: o specific test data available for this article. Refer to conditions to avoid and incompatible materials for additional information.
Chemical stability: This article is stable.
Possibility of hazardous reactions: Under normal conditions of storage and use, hazardous reactions will not occur.
Incompatible materials: Keep article away from strong acids, bases. The packaging will be affected by moisture.
Hazardous decomposition products: Carbon monoxide and carbon dioxide will be generated.
___________________________________________________________________________________

• TOXICOLOGICAL INFORMATION

On contact with eyes: May cause smarting and irritation.

On skin contact: Prolonged contact may defat and dry the skin leading to possible irritation and dermatitis.

On inhalation: Not applicable..

On ingestion: May cause irritation of the mouth, throat and digestive system.

Other health hazard information: None known.
___________________________________________________________________________________

• ECOLOGICAL INFORMATION

Toxicity: Not classified as dangerous.

Persistence and degradability: Biologically not degradable.

Bioaccumulative potential: This article is not expected to bioaccumulate through food chains in the environment.

Mobility in soil: This product is not likely to move rapidly with surface or groundwater flows because it is not soluble in water.
___________________________________________________________________________________

• DISPOSAL CONSIDERATIONS

Waste treatment methods - Product disposal: Dispose of in accordance with local regulations. Do not empty product into drains. According to the European catalogue, waste codes are not product specific, but application specific. The user should assign waste codes, preferably in discussion with the waste disposal authorities.

Packaging disposal: Dispose of in accordance with local regulations. Do not empty product into drains. The user should assign waste codes, preferably in discussion with the waste disposal authorities.

Hazardous waste: Consult an environmental professional to determine if local, regional or national regulations would classify spilled or contaminated materials as hazardous waste.
___________________________________________________________________________________

• REGULATORY INFORMATION

Safety, health and environmental regulations/legislation specific for the substance or mixture - Nature of hazard: No specific regulations or labelling requirements.

Hazard symbols: No specific regulations or labelling requirements.

R-phrases: No specific regulations or labelling requirements.

S-phrases: No specific regulations or labelling requirements.

EU Regulations: Classifications have been performed according to EU directives 1999/45/EC and 67/548/EEC as amended and adapted.

Chemical Safety Assessment: No chemical safety assessment has been carried out for this Article.

Date of issue: 1st January 2019

This Product Safety Data Sheet was prepared in compliance with article 31 and Annex II of the EU REACH regulation as well as their relevant amendments, on the approximation of laws, regulations and administrative provisions relative to the classification, packaging and labelling of dangerous substances and preparations.
It is the responsibility of the persons in receipt of this Product Safety Data Sheet to ensure that the information contained herein is properly read and understood by all people who may use, handle, dispose of or in any way come in to contact with the product.
All information and instructions provided in the Product Safety Data Sheet are based on the current state of scientific and technical knowledge at the date indicated on the present Product Safety Data Sheet. PR International Ltd shall not be held responsible for any defect in the product covered by this Product Safety Data Sheet, should the existence of such defect not be detectable considering the current state of scientific and technical knowledge.
___________________________________________________________________________________

• Detailed Ingredient List

Compound rubber.: No specific regulations or labelling requirements.

Butyl Rubber CAS No 9010-85-9
Polyisobutylene rubber CAS No 9003-27-4
Polybutene liquid rubber CAS No 9003-29-6
Calcium Carbonate CAS No 1317-65-3
Precipitated Calcium Carbonate CAS No 471-34-1
Talc CAS No 14807-96-6
Hydrocarbon Resin CAS No 64742-16-1
Factice CAS No 12653-61-1
Titanium Dioxide CAS No 13463-67-7
Stearic Acid CAS No 57-11-4
Antioxidant CAS No 6683-19-8

___________________________________________________________________________________